RHINO SHIELD APPLICATION PROCESS

Better Process.. Better Results


The Rhino Shield application involves a thorough process on every job.



We do it right, the first time so you Never Paint Again! Learn what to expect after requesting an estimate here.


Wondering what it is like to paint your home for the last time? Learn how a professional coating is done properly, the quality materials involved, and the exceptional service that gives your home the kind of advanced exterior our customers rave about.

Blue “As Seen on HGTV” logo with house roof icon

Pressure Wash


Before any of the work has begun, we pressure wash all of the surfaces to be done. Pressure washing removes dirt and debris from the substrate and provides a clean surface for the work to begin.

Two men standing outside a house, looking at each other in conversation.
Person painting a house exterior gray next to a taped window in bright sunlight

Thorough Inspection


We inspect all of the area to be coated and devise a plan to complete the project. Note which areas need “special attention”. Renail any loose nails and siding boards. Make an inventory of any wood that needs replaced, stucco needing repair, etc.

Repair/Replace Siding


We repair and replace all siding materials with the exact type of material as is on your home. Our goal is to bring the surface back to its original condition.

Worker repairing the exterior wall of a house with siding removed and exposed framing
Old weathered house with peeling white paint and ladders leaning against the front wall.

Hand Scraping


All loose paint and debris is hand scraped and removed. Our goal is to provide a clean bondable surface for the primer to be applied to.

Caulking


We fill small cracks and holes in the siding. We caulk all vertical joints. We ensure the caulking around window and doors is done properly to reduce air infiltration. We do not caulk underneath the laps as this limits ventilation. We use a high quality elastomeric acrylic caulk to ensure longevity and flexibility.

Worker cleaning a white house exterior on a ladder near two windows
House exterior windows and siding masked with blue painter’s tape and paper for painting

Masking


All areas which are not to be coated are masked off, covered, or temporarily removed (such as lighting fixtures, mailboxes, drainpipes, utility boxes, etc.) Special attention is given to roofing, plants, lawns, decks, windows, and other areas prone to overspray.

Apply Adhesive Primer Sealer


The primer is sprayed on to seal, waterproof, and provide a bonding agent for the finish coat. Our primer has a proprietary formula that includes fungicides, algaecides and mildewcides. Thus reducing future mold and mildew. It is white in color when applied and dries to a clear, tacky finish.

Worker painting the exterior of a white house while standing on a ladder
Worker using a pressure washer to clean ornate white moldings indoors

Apply Finish Coat


At last, after all the prep work and priming is completed, the ceramic top-coat is applied. This layer can be tinted to your choice of 1500 colors. The top-coat is sprayed at a rate of approximately 100 square feet per gallon or greater to achieve the optimal mil thickness. In some areas, brushing and rolling may be required. Porous surfaces may require back rolling.

Detail Touch Up


After the finish coat has been thoroughly applied, we touch up the detailed areas and tight space areas.

Person painting trim beneath roof eaves with a brush near red brick wall
Worker in white uniform sweeping debris from a driveway beside a parked white van

Clean Up


Once the finish coat had dried, we remove all masking masterials. Dropcloths are removed. Any shrubbery that was tied off is undone. Paint chips are clean up and even shop vacuumed if necessary. Our goal is to return your surroundings to the same condition as before we arrived.

Final Inspection


We’re not done until you’re completely satisfied with our work!

Two-story suburban house with gray roof and white garage, labeled “Engineered to outlast.”
Couple standing together, seen from behind, looking at a tan house in a suburban yard.

Application Process FAQs

  • What steps are involved in the Rhino Shield application process?

    Every Rhino Shield of Missouri job follows the same multi-step system: pressure washing, a full inspection, siding repairs, hand scraping, caulking, masking, an adhesive primer sealer, the ceramic finish coat, detail touch-up, cleanup and a final inspection. Skipping any of them shortens the life of the coating. Request an estimate and we'll walk you through the plan for your house.

  • How do you prepare the home's surface before coating?

    We pressure wash every surface first to strip off dirt and debris. Then we inspect the whole exterior, renail loose boards, and repair or replace damaged siding with the same material that's already on your home. All loose paint is hand scraped so the primer bonds to a clean, solid surface.

  • What does the primer layer do?

    The adhesive primer sealer seals and waterproofs the surface and gives the ceramic finish coat something to grip. Its formula includes fungicides, algaecides and mildewcides to help hold off future mold and mildew. It sprays on white and dries to a clear, tacky finish, which is how our crew knows it's ready for the topcoat.

  • How is this different from how most exterior painters in St. Louis paint a house?

    A typical repaint is a wash, some light scraping and a couple of coats of paint. Rhino Shield of Missouri adds siding repairs with matching material, elastomeric acrylic caulk, a mildew-resistant primer sealer and a ceramic finish coat sprayed to a set mil thickness. That extra prep is why the coating carries a 25-year written, transferable warranty.

  • How is the ceramic finish coat applied?

    The ceramic topcoat is mostly sprayed, at roughly 100 square feet per gallon or heavier, to reach the right mil thickness. Tight spots may be brushed or rolled, and porous surfaces like brick or rough stucco may be back-rolled to work the coating in. You can choose from about 1,500 colors.

  • Do you caulk every gap on the house?

    No, and that's on purpose. We fill small cracks and holes, caulk all vertical joints, and seal around windows and doors to cut air leaks. We don't caulk under the siding laps, because those gaps let the wall ventilate. We use a high-quality elastomeric acrylic caulk so the joints stay flexible for years.

  • Will your exterior painting contractors protect my windows and landscaping?

    Yes. Before any coating goes on, our crew masks or covers everything that isn't being coated and temporarily removes items like light fixtures, mailboxes and downspouts. Roofing, plants, lawns and windows get extra attention against overspray. Afterward we pull all masking, untie shrubs and clean up paint chips so your yard looks the way it did before we arrived. Questions? Call (314) 239-7947.